Because this is a MATCH barrel and not a "drop-in" barrel, this barrel must be fitted to your firearm by a competent gunsmith.  Our barrels are all made of 416 stainless steel bar stock with a Rockwell Hardness of 40-42. Our barrels have a twist rate of 1:16".

This conversion barrel is specific to the newest XD; the XDm. What is a conversion barrel? A conversion barrel allows you to convert your large caliber XD (.40SW or .357SIG) down to a smaller caliber (9x19) for the benefit of practice and plinking.

To increase reliability and performance, we always suggest that you use 9x19 magazines with our 9x19 barrel as well as reduced weight spring (18# or less).

When Springfield Armory released the XDm, XD fans took notice, especially competitive shooters. With its higher capacity, the XDm is a fantastic gun with USPSA Limited competition. It is for this reason that we set out to design & build a magwell that will allow our beloved XDm to run with gun with are 2x+ the cost.

We are very proud of our design and the quality of this magwell. We are certain that you will be too.

Are you looking to add some extra rounds to your magazine, whether for competition or practice? If so, this may be the product for you. Made of aluminum and with a removal backplate, this rugged design allows you to install your new spring, follower and extension in a minute or less. Unlike other magazine extension on the market, you will not need to fight with this one and it will NEVER come off of your mag tube during a reload.

When this extension is added to your XD^m magazine tube, it will bring your OAL to 170mm, making is legal for USPSA Open Division.

Capacity:

• 9x19 = 28+1 (+9 rounds)
• 40S&W = 25+1 (+9 rounds)

Magazine NOT included...

Attention Limited Shooters! PistolGear is proud to offer its 140mm magazine extension, designed by gamers for gamers. Made of aluminum and with a removal backplate, this rugged design allows you to install your new spring, follower and extension in seconds. Unlike other magazine extension on the market, you will not need to fight with this one and it will NEVER come off of your mag tube during a reload.

Capacity:

• 9x19 = 24+1 (+6 rounds)
• 40S&W = 20+1 (+4 rounds)

WARNING: SUPPLIES ARE LIMITED. IF WE ARE OUT, WE ARE SORRY. IT IS TOUGH TO GET COATED PARTS AT THIS TIME. 

This is a stainless steel guide for the Springfield XD^m. This rod weighs two ounces and uses the XDM's factory spring or these spring options.

Note: Unlike the stock guide rod, this rod is solid stainless steel - not hollow

Guide Rod sold under license from Don's Guide Rods

This is a stainless steel guide for the Springfield XD^m. This rod weighs two ounces and uses the XDM's factory spring or these spring options.

Note: Unlike the stock guide rod, this rod is solid stainless steel - not hollow

Guide Rod sold under license from Don's Guide Rods

The PistolGear slide stop is very near and dear to our heart. We set out to build this part some time ago, looking to create a solution that would not only help your traditional XD owner, but the non-traditional owner as well.

Our design allows any XD owner, even those who lack dexterity in their thumb, or those who have trouble hitting the slide stop because of small hands, to quickly and easily close the slide from the lock-back position.

We believe that this part will have a great impact on all who give it a try. If you are a competition shooter (like we are), you will find this part to be fast and unobtrusive.

This kit is required if you are looking to maximize your hold on your XD^m. The kit include four parts to be used as you see fit, based on your needs.

The large piece is for the front and side straps. The rectangular part is for the rear strap. The two triangular pieces are for filling in the gap.

Texture: Sand

Color: Black

Dimensionally accurate to the factory part, this Striker Spring Guide is made of aluminum and will not crack or break like the stock plastic version has been known to do.

Silver finish on this part adds a nice contrast and a little bling.

Note: Part will fit ALL XD and XDm models.

Made by Don's Guide Rods

Dimensionally accurate to the factory part, this Striker Spring Guide is made of aluminum and will not crack or break like the stock plastic version has been known to do.

Note: Part will fit ALL XD and XDm models.

Made by Don's Guide Rods

This conversion barrel is specific to the newest XD; the XDm. What is a conversion barrel? A conversion barrel allows you to convert your large caliber XD (.40SW) down to a smaller caliber (357SIG) for the benefit of practice and plinking.

Note: For this barrel, you can run your factory spring weight as well as your factory 40S&W magazines.

For those looking to attach a "can" or compensator onto their XDM, this barrel will allow you to do so. Each barrel is made from 416 Stainless Steel and includes 1:16" twist unless selected otherwise.

Each barrel is a semi drop-in configuration and includes a thread protector. 

MADE IN THE US

This spring pack from Canyon Creek includes the seven springs crucial to the operation of the XD. No XD owner should be without this kit. Testing has shown that this kit will reduce the stock trigger weight by as much as two pounds*.

PistolGear is proud to offer the first IDPA legal magwell to the XD^m marketplace. Tweaking our design for the benefit of an affective product that will fit the IDPA box, this magwell will make your ESP machine rock!

The PistolGear "Operator" magwell for the XD^m doubles the width of the frame funnel for the benefit of smoother tactical reloads. The magwells locks onto the frame in two locations making it rigid. The magwell is held in place by a threaded pin that replaces the factory grip insert pin, making installation easy and non-permanent. YOU DO NOT EPOXY THIS PRODUCT TO YOUR FRAME.

Note: Designed to work with the #2 grip insert.

Designed and used by multi-world and national practical shooting champion, Dave Sevigny, you will agree that this rear sight is the fastest available on the XD market today.

In today's market, as it applies to gun sights, it is rare that someone comes across a design that is so effective that the "pros" take notice. When Scott Warren released his idea for the perfect set of sights, it wasn't long before folks noticed the solid design  and its benefits.

Springer Precision has coupled their XD Sear and a host of springs for the benefit of improving the XDm's stock trigger. With this pairing of parts, you are one step closer to a full-house trigger job. The results of the kit is a shorter, lighter, crisper trigger pull. Our testing shows that this setup will reduce your trigger's pre-travel by 50% and your trigger pull weight by 25% (two pounds or more).

Kit Includes: Polished Reduced Travel Sear, Sear Spring, Trigger Spring, Striker Springer, Striker Safety Spring and LCI Spring

9mm Major is quickly becoming popular for many reasons. Because of its popularity, XD fans are turning their beloved XDs into Open "Race Guns". Springer Precision has heard the call from gamers and is proud to market the first compensator for the XD & XDm. We are proud to offer it to our customers.

You have the option of 1, 2 or 3 holes for the XD. All XDm Compensators will include 3 holes. One hole is good for light/minor loads. Two holes is a good option for factory ammunition. Three holes is best for 9x19 Major loads.

Thread Specifications: 1/2" x 28 (choose "Springer Precision Compensator" option if ordering PistolGear threaded barrel)

If you are looking for a brighter front sight, whether it be for plinking, competition or aging eyes, this is a great option. This front sight fits all Springfield XD models and is to be used with the stock XD rear sight. There is a resin overmolded LitePipe which protects the fiberoptic rod.

HIVIZ Dovetail Sight Installation Warning!! HIVIZ dovetails are manufactured slightly oversize to allow for dovetail cut wear on used guns. Fitting will likely be necessary for proper installation. We recommends gunsmith installation, as damage caused during installation is NOT covered by warranty.


 

Note:This is a 3-Dot Configuration, with Fiber Optic in both the front & rear.

The height of this front sight is equal to that of your stock sight, allowing you to use your existing rear sight.

Note 1: Button compatible with all XDs.

Note 2: Not legal for USPSA Production nor IDPA.

Note: Color of this item is BLACK

This holster is compatible with all XD calibers.

This holster is compatible with all XD calibers.

This speed loader was designed to work with full-size magazines and is compatible with fullsize XD magazines. It is not compatible with XDSC magazines.

Introduction & Tutorial Video 

This holster is made specifically for the Springfied XDm. The holster profile matches that of the firearm, for the benefit of a low-friction draw.

This holster has a speed-cut for an ultra fast presentation, and ease of re-holstering. Twin tension screws, allow for precise retention adjustment. Excellent for daily carry, practice, and competition. Includes Tek-Lok.

Blade-Tech is proud to offer this new magazine pouch to XD enthusiasts. This mag pouch will work with both XD and XDm magazines (not XD45ACP mags) and is one of the fastest designs available today. USPSA Shooters rejoice!

Only available in RH at this time, to be placed on left hip.

The Canyon Creek Tungsten Guide Rod for the XDm is nearly three times the weight of the XDm's stock guide rod. By adding this nonreciprocating mass to the muzzle end of the gun, you ease both muzzle flip and felt recoil.  An Independent test showed that the use of a Tungsten Guide Rod reduced split times on a double tap by 37% (meaning quicker follow up shots) over a stock weight guide rod.

Guide Rod Weighs 4 ounces and dimensionally similar to your stock guide rod (no bushing required).
 

This dual magazine pouch by RESCOMP builds on their success of the Versa-Pouch by putting two pouches on a single platform. The belt-loop portion of this product will accommodate of belt size up to 1.65" without modification. If you have a larger belt, you can remove the separator and the loop will allow a belt width up to 2.5".

This product is perfect for both IDPA and USPSA competition.

This product is compatible with XD magazines with the following calibers: 9x19, .357SIG, 40S&W, 45GAP, 45ACP

• One Pouch for a multitude of different magazines.
• Available in black

This ''Follower Kit'' includes a ''Grams Format'' follower and 11 coil spring. It will fit XDm magazines that measure up to 145mm in length (with base pad attached). Will work with 9MM and 40SW/357SIG Calibers.

This kit is compatible with both PistolGear (140mm) and Arrendondo extensions and will allow you to run with 19 or 20 rounds in 40SW magazines and 23 to 24 in 9mm magazines.

Note: Because of the design for the benefit of maximum capacity, your slide will not lock back when the magazine is empty.

Grip Gloves are custom molded for each pistol model. Ideal for polymer frame handguns with no replacement grips available. Made from Pachmayr Decelerator material, Grip Gloves deliver enhanced control and will absorb recoil. The custom fit feels like an extension of your handgun grip. The ultra-soft, ultra-stretchy material makes installation a snap. No trimming, no need for soap and water. Distinctive ventilated side panels and finger grooves provide more instinctive gun orientation and a professional look. Tactical Grip Gloves are the only Slip-Ons that “fit like a glove.” 

The brightest night sight available for the XD/XDm is available to you at a great price.

Tritium/Fiber Optic Sights

The brightest night sight available for the XD/XDm is available to you at a great price.

Tritium/Fiber Optic Sights

Note: By design, to reduce distraction, the yellow WILL NOT glow as bright as green.

• One Pouch for a mulititude of different magazines.
• Ambidexterous construction.
• Available in black
• Belt width up to 1.5", thickness up to 0.25"

This product is compatible with XD magazines with the following calibers: 9x19, .357SIG, 40S&W, 45GAP, 45ACP

The mount that's used by more Master competitors in Glock competitions is "now" available for the Springfield XD. The CARVER Mounting system secures your red dot sight for limited dot "jump" to help improve your scores. All CARVER Mounting systems are CNC machined from high grade aircraft aluminum and consist of 5 parts that are interchangable. Competition models can be converted to Hunter models by buying optional uprights. Installation is easy, with no gunsmithing required. Front and rear sights are required to be removed for use of the Competition model due to the low positioning of the red dot sight over the slide. CARVER Hunter XD mount fits all Springfield XD handguns except the Sub-Compact model.

Note: Mount color is BLACK

The CARVER Mounting system secures your red dot sight for limited dot "jump" to help improve your scores. All CARVER Mounting systems are CNC machined from high grade aircraft aluminum and consist of 5 parts that are interchangable. Hunter models can be converted to Competition models by buying optional uprights. Installation is easy, with no gunsmithing required. Front and rear sights can remain on the slide with the use of the Hunter model.

Note: CARVER Hunter XD mount fits all Springfield XD handguns except the Sub-Compact model.

Color: BLACK

This is a factory magazine for the Springfield XDm in 40S&W. This magazine's capacity is 16 rounds.

This is a 19 round factory magazine for the Springfield XD^m 9x19.

There is little that is more frustrating than when you lose a small part during cleaning or teardown. Best to keep a couple of pins in your bag, just in case.

Three Pins per Pack.

Note: This is not a striker retainer pin. This is the pin that secures the XDm back-strap to the frame.

Finally, springs for the Springfield XD^m that will allow you to tune your gun to your loads. These springs will work with both the stock XD^m Guide Rod as well as Don's Guide Rod for the XD^m.

• Reduced Power Loads: 14 & 16 Pounds
• Factory Level Loads: 18 Pounds
• +P Loads: 20 & 20 Pounds