Because this is a Match barrel and not a "drop-in" barrel, it needs to be fitted by a competent gunsmith.

Our barrels are made of 416 stainless steel bar stock, a Rockwell Hardness of 40-42 with a twist rate of 1:16".

Note 1: Barrels will not fit the XDSC

Note 2: All barrels will require fitting

Note 3: Since the length of the Match barrel need to be cut and crowned during fitting, this barrel will fit both Service/Compact and Tactical length models.

Note 4: All barrels are silver in color due to the stainless steel material.

We are proud to offer our own brand of XD conversion barrels to the marketplace. What is a conversion barrel? A conversion barrel allows you to convert your large caliber XD (.40SW or .357SIG) down to a smaller caliber (9x19) for the benefit of practice and plinking.

To increase reliability and performance, we always suggest that you use 9x19 magazines with our 9x19 barrel.

Note: If you are going to run this barrel in the XD-M, you will need to order the "Tactical" version and have the length cut and crowned if you want a flush fit. If not, the barrel will extend beyond the end of the slide by roughly 1/2 inch. 

The PistolGear Semi Drop-In Barrels are made to factory specification, with a few added twists. The dimensions are over-sized in a few keys areas, yet we designed the barrels to where they will drop into approximately 90% of the XDs & HS2000s out there (hence the name semi-drop in). Unlike the XD’s stock barrel which is carbon steel, our barrels are made from 416 stainless steel; the same material used in our “Match” barrels.

Note: If you have a Service model, the Tactical barrels will fit your gun; however the barrel will extend beyond the slide.

Note: This is NOT a conversion barrel!

The PistolGear "Operator" is the first magwell available for the XD that is not proprietary. What does this mean? It means that you can use your stock magazines or inexpensive extensions (e.g. AGP Arms, Arredondo) and not break the bank by purchasing expensive proprietary basepads. The funnel of the magwell increases the area by 30%, making tactical reloads both easier and smoother.

If you use stock magazines with this product, you will need to use an extension of sorts, since the base of the magazine will be below the funnel of the magwell. We suggest the use of the PistolGear "Slam Pads".

This magwell is IDPA legal and is perfect for Law Enforcement as well.

This product is for the XD 9x19 / .357SIG / .40S&W / .45GAP Models only! It will not fit on XD45ACP nor XDm Models.

Note: Pins are packed three to a pack. This is not a factory part.

Schematic #: 35

Achtung, Gamers! The PistolGear "UnLimited" is the first magwell available for the XD that is not proprietary. What does this mean? It means that you can use your stock magazines or inexpensive extensions (e.g. AGP Arms, Arredondo) and not break the bank because you were forced into purchasing expensive proprietary basepads. The funnel of the UnLimited Magwell increases the target area by 50%; in essence doubling your target.

If you use stock magazines with this product, you will need to use an extension of sorts, since the base of the magazine will be below the funnel of the magwell. We suggest the use of the PistolGear "Slam Pads".

Click here to see a picture of the XD45ACP Magwell

This product will not fit the XD Subcompact models. Some fitting may be required.

PistolGear is proud to offer the first Slam Pad specifically for the Springfield XD. What is a “Slam Pad”? A Slam Pad is a dense piece of precision cut rubber that closely matches the shape of the XD Magazine’s base pad, in order to protect the magazine from the ground during reloads and/or to add some additional length to the magazine in order to aid during reloads. Each Slam Pad has a hole in the center that will allow you to remove your magazine base pad for cleaning without having to remove your Slam Pad.

This product is compatible with any of the PistolGear Magwells and is perfect for both IDPA and Limited 10 competition. Each of the Slam Pads includes an aggressive adhesive that will keep them in place for as long as you want them installed. If you want to remove them, you merely pull them off.

Each pack includes five (5) pads and a tube of Super Glue for those who want to permanently affix their pads.

When Springfield Armory released the XDm, XD fans took notice, especially competitive shooters. With its higher capacity, the XDm is a fantastic gun with USPSA Limited competition. It is for this reason that we set out to design & build a magwell that will allow our beloved XDm to run with gun with are 2x+ the cost.

We are very proud of our design and the quality of this magwell. We are certain that you will be too.

Note: Designed to work with the #2 grip insert.

This spring pack from Canyon Creek includes the five springs crucial to the operation of the XD. No XD owner should be without this kit. Testing has shown that this kit will reduce the stock trigger weight by as much as two pounds*.

Spring Kit includes:

• Striker Saftey Spring
• Striker Spring
• Trigger Bar Spring
• Sear Spring
• Rebound Spring

* Will not reduce the travel and reset distance of the trigger pull. Spring will only affect the weight of the trigger pull

Note: Spring Pack springs are compatible with the Springer Precision Sear

An Independent test conducted showed that the use of a Tungsten Guide Rod reduced split times on a double tap by 37% (meaning quicker follow up shots) over a stock weight guide rod.

Note: Must use the include spring with the Tungsten Service Rod.

An Independent test showed that the use of a Tungsten Guide Rod reduced split times on a double tap by 37% (meaning quicker follow up shots) over a stock weight guide rod.

Note: Will not fit the XD45ACP or XD-M models

Note: Rods for the Service model will include the required bushing.

Note 2: Spring not included!

Bushing shown within red square, Guide Rod not included.

1If you are looking to upgrade your stock guide rod to something with more weight and a little "bling", consider Don's "Fat" Rod. This rod uses the stock spring and weighs roughly 2.2 ounces.

Click here for compatible springs!

Building on his successful rods for the Springfield XD, Don's latest Guide Rod is a stainless steel version that is a clone to the factory rod. This rod weighs two ounces and uses your XD-M's factory spring.

Note: Unlike the stock guide rod, this rod is solid stainless steel 

In today's market, as it applies to gun sights, it is rare that someone comes across a design that is so effective that the "pros" take notice. When Scott Warren released his idea for the perfect set of sights, it wasn't long before folks noticed the solid design  and its benefits.

Brought to you by the American Gunsmith Institute, Master Gunsmith Bob Dunlap uses a custom cutaway XD to teach you the complete disassembly and assembly (not just field stripping), parts identification, proper cleaning and lubrication, & step-by-step instruction in design, function, and repair.

Runtime: 88 Minutes

• High quality product

• Product color validates placement

• Adheres to the metal, will not run off

• Will not evaporate

• Will stay intact even during pouring rain

• 4 times the film strength of molybendium grease

• Needle included for precision application

• Yield roughly 50,000 rounds

• Not a grease, it's an oil

Note: Mag Spacers are black.

Springer Precision has coupled their XD Sear and a host of springs for the benefit of improving the XD's stock trigger. With this pairing of parts, you are one step closer to a full-house trigger job. The results of the kit is a shorter, lighter, crisper trigger pull. Our testing shows that this setup will reduce your trigger's pre-travel by 50% and your trigger pull weight by 25% (two pounds or more).

Please note this product will not work with the XD45ACP model(s) that include the thumb safety levers, nor the XDm.

If you reload and use "hard" primer such as Winchester or CCI, you may need to use your stock striker spring.

If you are looking to further reduce your XD's reset, you need one of these. CNC machined from 17-4 stainless steel billet, this product will give you the means to further mod your XD for gaming, offering a short & crisp trigger pull.

Note 1: To be used with the "Trigger Upgrade Kit for XD" only! Will not work with the stock sear!!

Note 2: Trigger bar must be fitted in order to operate properly.

Springer Precision has coupled their XD Sear and a host of springs for the benefit of improving the XDm's stock trigger. With this pairing of parts, you are one step closer to a full-house trigger job. The results of the kit is a shorter, lighter, crisper trigger pull. Our testing shows that this setup will reduce your trigger's pre-travel by 50% and your trigger pull weight by 25% (two pounds or more).

Kit Includes: Polished Reduced Travel Sear, Sear Spring, Trigger Spring, Striker Springer, Striker Safety Spring and LCI Spring

If you reload and use "hard" primer such as Winchester or CCI, you may need to use your stock striker spring.

NOTE: THIS KIT IS ONLY FOR XDm MODELS! In order to use this product, you will need to remove the auto take-down feature from the firearm.

9mm Major is quickly becoming popular for many reasons. Because of its popularity, XD fans are turning their beloved XDs into Open "Race Guns". Springer Precision has heard the call from gamers and is proud to market the first compensator for the XD. We are proud to offer it to our customers.

You have the option of 1, 2 or 3 holes. One hole is good for light/minor loads. Two holes is a good option for factory ammunition. Three holes is best for 9x19 Major loads.

The theory behind the design of the ear muff (and ear plug as well) is to attempt to block all sound from entering the ear. The only way a muff can accomplish this is to create a seal around the outer ear and add material to block the sound. That is why the higher NRR (Noise Reduction Rating) muffs are generally the heaviest. The ZEM uses new and entirely different technology. The patented ZEM technology directs sound away from the ear and cancels it. The ZEM achieves a high NRR without adding bulk.

Note: Each set of ZEMs includes to sets of cuffs

Note: The FLAT BLACK color we carry is very close to the stock finish on the XD.

The EVOlution Range Bag by i-SHOT is the most adaptable solution to date. This bag is revolutionary because of its design and use of material. If you are looking to purchase a range bag that will last as long as you do, a bag that will grow as you grow, this is the bag for you.

Color: Black with Black

CLICK HERE TO SEE A LARGER IMAGE

If you are looking for a brighter front sight, whether it be for plinking, competition or aging eyes, this is a great option. This front sight fits all Springfield XD models and is to be used with the stock XD rear sight. There is a resin overmolded LitePipe which protects the fiberoptic rod.

HIVIZ Dovetail Sight Installation Warning!! HIVIZ dovetails are manufactured slightly oversize to allow for dovetail cut wear on used guns. Fitting will likely be necessary for proper installation. We recommends gunsmith installation, as damage caused during installation is NOT covered by warranty.


 

Building on the success of ZEMS, the SensGard ZEM SG-31 was designed for high intensity noise activities, such as shooting. Recommended for any noise above 110 decibels, the SG-31 offers the patented Zwislocki protection from damaging noise while allowing speech and other useful sounds to be heard. Locking nylon headband positions the SG-31 firmly and comfortably on your head.

At just 1.7 ounces, get 21st century noise cancellation technology without bulk or batteries. The SG-31 is perfect for those who are looking for a light-weight solution during warm weather and for those who shoot both indoors and out.

The SG-31 is durable and folds to fit in your pocket.

Includes Replacement Cuff 4-Pack.

Color: Black Only

Note:This is a 3-Dot Configuration, with Fiber Optic in both the front & rear.

The height of this front sight is equal to that of your stock sight, allowing you to use your existing rear sight.

All sights meet strict quality standards before being shipped and all processes are performed, controlled, and monitored to demanding quality levels.

Note: Not to be used on XD45ACP Models.

Set includes Red fiber in the front and Green fiber in the rear.

This set includes both the front and rear sights and is specific to the XD.

The patented T.F.O. formula gives you the daytime advantages of fiber optic sights and the lowlight advantages of night sights, making this sight set the "ultimate handgun sight”.

This set includes both the front and rear sights

G/G = Green Front, Green Rear

G/Y = Green Front, Yellow Rear

TRUGLO TRITIUM SIGHT FOR XD
PERFECT FOR LOW-LIGHT ENCOUNTERS

• Traditional tritium night sights.
• Uses the brightest tritium available.
• CNC machined steel construction.
• Green front and rear.
• Fits standard holsters.
• Snag resistant design.

Note: This brush is for staggered mags in 9mm-45ACP, such as those for the XD, Glock, CZ, Beretta, etc.