Shop By XD Models

Shop By Product Category

I'm sorry, that particular option is currently out of stock.

Please enter your email address and we'll email you when this product is back in stock.

Home » Shop by Product Type » Magazine or Magazine Parts

PistolGear Slam Pads for XD/XDm (0.250") - FIVE PACK

Price: $15.00

Based on 5 ratings. (View)

Email Friend | Ask A Question

Quantity:

THIS PRODUCT NOW USES 3M RP32 ADHESIVE - A HIGH STRENGTH, HIGH TEMP BOND ADHESIVE

A Slam Pad is an inexpensive way increasing your magazine's overall length. The extra length is usually required when using a magwell. Since the Slam Pads are made of rubber, the pads will offer your magazines a little protection when your magazines are dropped during a reloads.

The two-hole design of this product will allow it to fit all XD and XD(m) magazines, regardless of caliber, as well as many brands of magazines beyond Springfield magazines. This product is too wide for XD Slim magazines.

Sold in a pack of five (5).
Each pad includes a pressure sensitive adhesive
Thickness: 0.250"
Too large for XD Slim Magazines
Some fitting (reducing pad thickness) may be required for your application
Note: This product, when used with XD(m) magazines, will fit the IDPA box, however, you must check your gun with an available IDPA box in order to make sure that your specific gun is IDPA legal.

IDPA SSP & ESP LEGAL!

WARNING: This product can expose you to Lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to - www.P65Warnings.ca.gov

« Previous | Next »

5 Product Reviews - Average rating 4.2 / 5 (Show All)

Click to review this product

Did not fit in IDPA Box

Bob H. - 09th May 2016

Did not Fit in IDPA Box. Used these pads at MD State Championship Match with XDm .40 5.25". Got to Stage 2 and could not get gun in IDPA box. Match director got plexiglass box to ensure box was proper size. Tried multiple time to fit gun in box including compressing rear sights. finally gave up. I was given a DNF for match but was allowed to shot and receive unofficial score. Would have finished 4th in my classification and best Distinguished Senior. [PG NOTE: In speaking with the customer regarding his experience with this product, we determined that the base pads were not the problem as much as how the magazine stock base pad was hitting the installed magwell. This contact eliminated any play that would have allowed the customer's gun to fit the IDPA box as required. As noted on our website, we suggest that all customers who shoot competitively make certain they measure and weigh their specific gun before heading to any major match.

Great Fit for IDPA

Joe K - 20th February 2014

Using these on an XDm 5.25 (9mm), with an Operator magwell... combination works fantastic; and "fits in the box"... I don't think the 3/8 pads would fit in the box on my gun; the 1/4 inchers make it, but with little room to spare. Highly recommend these; along with the Operator magwell, my times are much faster...

Contact Cement

Joe K - 20th February 2014

Forgot to say in my review that I contact cemented these pads on my mags... I doubt the adhesive that was on them would have held for very long. Once you decide that you are going to use them, cement them on permanently. Contact cement holds them very well, and provides somewhat of a flexible bond.

just right...

gundevil - 14th May 2010

The .250 slam pads are perfect for IDPA for both operator magwells on my XD and XDM. (Note: If you use the thicker slam pad, it will not fit properly in the IDPA box.) Easy to put on, takes just a few seconds.

Perfect Fit!

John Canton - 09th July 2009

I bought some of these because we shoot indoors a lot. I was hoping that the rubber pad would save my mags a bit. They work very well and now when the magazine hits the concrete, I don't cringe. I did not use the super glue. The adhesive is pretty strong.

Click to review this product

RELATED PRODUCTS